Ordin nr.4 din 20.01.2015 cu privire la aprobarea Listei standardelor moldoveneşti prin care se adoptă standarde europene armonizate la Reglementarea tehnică "Maşini industriale"

Nota 4

prezumţia de conformitate a standardului înlocuit

Nota 1

Standarde de tip A

Standardele de tip A specifică conceptele de bază, terminologia şi principiile de proiectare aplicabile tuturor categoriilor de maşini. Aplicarea exclusivă a acestor standarde, deşi reprezintă un cadru esenţial pentru aplicarea corectă a Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014, nu este suficientă pentru asigurarea conformităţii cu cerinţele esenţiale de sănătate şi siguranţă din Reglementarea tehnică şi, prin urmare, nu conferă o prezumţie totală de conformitate.

Safety of machinery - General principles for design - Risk assessment and risk reduction

SM SR EN ISO 12100-2:2011

Nota 2

EN ISO 14121-1:2007

Nota 2

Standarde de tip B

Standardele de tip B abordează aspecte specifice siguranţei maşinilor sau diferite tipuri de protecţie care pot fi utilizate pentru o gamă largă de maşini. Aplicarea specificaţiilor standardelor de tip B conferă o prezumţie de conformitate cu cerinţele esenţiale de sănătate şi siguranţă ale Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014 la care acestea se referă dacă un standard de tip C sau evaluarea riscurilor de către producător arată că o soluţie tehnică specificată de standardul de tip B este adecvată pentru categoria sau modelul specific de maşina în cauză. Aplicarea standardelor de tip B care oferă specificaţii pentru componentele de siguranţă care sunt introduse pe piaţă separat conferă o prezumţie de conformitate pentru componentele de siguranţă în cauză şi pentru cerinţele esenţiale de sănătate şi siguranţă care fac obiectul standardelor.

Safety of machinery - Minimum gaps to avoid crushing of parts of the human body

Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery

Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings

Safety of machinery - Human body measurements - Part 3: Anthropometric data

Safety of machinery - Two-hand control devices - Functional aspects - Principles for design

Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles

Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks

Safety of machinery - Visual danger signals - General requirements, design and testing

Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays

Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators

Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 4: Location and arrangement of displays and control actuators

Safety of machinery - System of auditory and visual danger and information signals

Safety of machinery - Human physical performance - Part 1: Terms and definitions

Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation

Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery

Mechanical vibration - Testing of mobile machinery in order to determine the vibration emission value

Safety of machinery - Prevention of unexpected start-up

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 3: Test bench method for the measurement of the emission rate of a given pollutant

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4: Capture efficiency of an exhaust system - Tracer method

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Separation efficiency by mass, unducted outlet

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Separation efficiency by mass, ducted outlet

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 8: Pollutant concentration parameter, test bench method

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index

Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology

Nota 2

Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining

Nota 2

Mechanical vibration and shock - Vibration isolation of machines - Information for the application of source isolation

Safety of machinery - Integral lighting of machines

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms

Nota 2

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room

Nota 2

Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane

Nota 2

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for anechoic rooms and hemi-anechoic rooms

Nota 2

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for anechoic rooms and hemi-anechoic rooms

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane

Nota 2

Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment

Nota 2

Hydraulic fluid power - General rules and safety requirements for systems and their components

Nota 2

Pneumatic fluid power - General rules and safety requirements for systems and their components

Nota 2

Acoustics - Declaration and verification of noise emission values of machinery and equipment

Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method

Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss

Ergonomics - Danger signals for public and work areas - Auditory danger signals

Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points

Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning

Mechanical vibration - Laboratory method for evaluating vehicle seat vibration - Part 1: Basic

Nota 2

Safety of machinery - Integrated manufacturing systems - Basic requirements

Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions

Nota 2

Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections

Nota 2

Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections

Nota 2

Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level

Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections

Nota 2

Acoustics - Noise emitted by machinery and equipment - Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity

Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes)

Acoustics - Determination of sound insulation performances of enclosures - Part 2: Measurements in situ (for acceptance and verification purposes)

Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning

Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method

Acoustics - Determination of sound insulation performance of cabins - Laboratory and in situ measurements

Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 1: General principles

Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 2: Radiation emission measurement procedure

Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 3: Reduction of radiation by attenuation or screening

Screens for laser working places - Safety requirements and testing

Nota 2

Screens for laser working places - Safety requirements and testing

Safety of machinery - Requirements for the drafting of the vibration clauses of safety standards

Mechanical vibration - Industrial trucks - Laboratory evaluation and specification of operator seat vibration

Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces

Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 3: Cold surfaces

Mechanical vibration and shock - Hand-arm vibration - Method for measuring the vibration transmissibility of resilient materials when loaded by the hand-arm system

Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design

Nota 2

Safety of machinery - Safety-related parts of control systems - Part 2: Validation

Nota 2

Safety of machinery - Emergency stop function - Principles for design

Nota 2

Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts of the human body

Nota 2

Safety of machinery - Pressure-sensitive protective devices - Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors

Nota 2

Safety of machinery - Pressure-sensitive protective devices - Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars

Nota 2

Safety of machinery - Pressure-sensitive protective devices - Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices

Nota 2

Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs

Safety of machinery - Interlocking devices associated with guards - Principles for design and selection

Nota 2

Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards

Nota 2

Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access

Nota 2

Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways

Nota 2

Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails

Nota 2

Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders

Nota 2

Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers

Nota 2

Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures

Nota 2

Safety of machinery - Hygiene requirements for the design of machinery

Safety of machinery - Anthropometric requirements for the design of workstations at machinery

Ergonomics - Computer manikins and body templates - Part 1: General requirements

Determination of maximum explosion pressure and the maximum rate of pressure rise of gases and vapours

Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 1: General principles for design and development

Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 2: Concept phase

Safety of machinery - Fire prevention and fire protection

Nota 2

Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission

Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission

Standarde de tip C

Standardele de tip C oferă specificaţii pentru o categorie dată de maşini. Diferitele tipuri de maşini aparţinînd categoriei care face obiectul unui standard de tip C au o destinaţie asemănătoare şi prezintă riscuri similare. Standardele de tip C se pot referi la standarde de tip A sau B, indicând care dintre specificaţiile standardelor de tip A sau B se aplică categoriei de maşini în cauză. Atunci cînd, pentru un anumit aspect al siguranţei maşinilor, un standard de tip C se îndepărtează de specificaţiile unui standard de tip A sau B, specificaţiile standardului de tip C au întâietate faţă de specificaţiile standardului de tip A sau B. Aplicarea specificaţiilor unui standard de tip C pe baza evaluării riscurilor de către producător conferă o prezumţie de conformitate cu cerinţele esenţiale de sănătate şi siguranţă ale Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014, care fac obiectul standardului. Anumite standarde de tip C se compun din mai multe părţi, partea 1 a standardului oferind specificaţii generale aplicabile unei familii de maşini, în timp ce alte părţi ale standardului precizează specificaţiile anumitor categorii de maşini care aparţin familiei, completând sau modificând specificaţiile generale din partea 1. În cazul standardelor de tip C organizate în acest mod, prezumţia de conformitate cu cerinţele esenţiale de sănătate şi siguranţă ale Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014 este conferită prin aplicarea părţii generale 1 a standardului împreună cu partea specifică corespunzătoare a standardului.

Safety rules for the construction and installation of lifts - Part 3: Electric and hydraulic service lifts

Safety rules for the construction and installation of lifts - Part 3: Electric and hydraulic service lifts

Safety rules for the construction and installation of lifts - Lifts for the transport of goods only - Part 31: Accessible goods only lifts

Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 40: Stairlifts and inclined lifting platforms intended for persons with impaired mobility

Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 41: Vertical lifting platforms intended for use by persons with impaired mobility

Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes

Safety of escalators and moving walks - Part 1: Construction and installation

Nota 2

Plastics and rubber machines - Injection moulding machines - Safety requirements

Automatic forced draught burners for liquid fuels

Nota 2

Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests

Nota 2

Plastics and rubber machines - Compression moulding machines and transfer moulding machines - Safety requirements

Nota 2

Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking

Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation

Nota 2

Safety of packaging machines - Part 1: Terminology and classification of packaging machines and associated equipment

Nota 2

Safety of packaging machines - Part 3: Form, fill and seal machines

Safety of packaging machines - Part 5:

Wrapping machines

Safety of packaging machines - Part 6: Pallet wrapping machines

Nota 2

Safety of packaging machines - Part 7: Group and secondary packaging machines

Safety of packaging machines - Part 8: Strapping machines

Safety of packaging machines - Part 9: Noise measurement methods for packaging machines, packaging lines and associated equipment, grade of accuracy 2 and 3

Safety of packaging machines - Part 10: General Requirements

Plastics and rubber machines - Blow moulding machines - Safety requirements

Food processing machinery - Dough mixers - Safety and hygiene requirements

Nota 2

Food processing machinery - Planetary mixers - Safety and hygiene requirements

Nota 2

Earth-moving machinery - Safety - Part 1: General requirements

Nota 2

Earth-moving machinery - Safety - Part 1: General requirements

Atenţie: Prezenta publicaţie nu priveşte clauza 5.8.1 Vizibilitate - Câmpul vizual al operatorului din acest standard, a cărei aplicare nu conferă o prezumţie de conformitate cu cerinţele esenţiale de sănătate şi siguranţă prevăzute de pct.33-41şi pct.193-195 din Anexa nr.1 la Reglementarea tehnică "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014

.

Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozers

Earth-moving machinery - Safety - Part 3: Requirements for loaders

Earth-moving machinery - Safety - Part 4: Requirements for backhoe loaders

Earth-moving machinery - Safety - Part 5: Requirements for hydraulic excavators

Nota 2

Earth-moving machinery - Safety - Part 6: Requirements for dumpers

Earth-moving machinery - Safety - Part 7: Requirements for scrapers

Earth-moving machinery - Safety - Part 8: Requirements for graders

Earth-moving machinery - Safety - Part 9: Requirements for pipelayers

Earth-moving machinery - Safety - Part 10: Requirements for trenchers

Earth-moving machinery - Safety - Part 11: Requirements for earth and landfill compactors

Earth-moving machinery - Safety - Part 12: Requirements for cable excavators

Mobile road construction machinery - Safety - Part 1: Common requirements

Mobile road construction machinery - Safety - Part 2: Specific requirements for road-milling machines

Mobile road construction machinery - Safety - Part 3: Specific requirements for soil-stabilising machines and recycling machines

Mobile road construction machinery - Safety - Part 4: Specific requirements for compaction machines

Nota 2

Mobile road construction machinery - Safety - Part 6: Specific requirements for paver-finishers

Rail dependent storage and retrieval equipment - Safety requirements

Road construction machines - Mixing plants for road construction materials - Safety requirements

Agricultural and forestry machinery - Safety of log splitters - Part 1: Wedge splitters

Nota 2

Agricultural and forestry machinery - Safety of log splitters - Part 2: Screw splitters

Continuous handling equipment and systems - Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers

Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors

Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads

Continuous handling equipment and systems - Safety and EMC requirements for fixed belt conveyors for bulk materials

Automatic forced draught burners for gaseous fuels

Automatic forced draught burners for gaseous fuels

Agricultural machinery - Manure spreaders - Safety

Nota 2

Machine tools - Mechanical presses - Safety

Machine tools - Safety - Hydraulic presses

Nota 2

Agricultural machinery - Silage loading, mixing and/or chopping and distributing machines - Safety

Agricultural machinery - Vine shoot tipping machines - Safety

Agricultural machinery - Slurry tankers - Safety

Agricultural and forestry machinery - Pedestrian controlled tractors with mounted rotary cultivators, motor hoes, motor hoes with drive wheel(s) - Safety

Nota 2

Safety requirements for foundry moulding and coremaking machinery and plant associated equipment

Safety requirements for foundry moulding and coremaking machinery and plant associated equipment

Continuous handling equipment and systems - Safety requirements for systems and their components for pneumatic handling of bulk materials

Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment

Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems

Industrial thermoprocessing equipment - Part 3: Safety requirements for the generation and use of atmosphere gases

Garden equipment - Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers - Mechanical safety

Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools

Pumps and pump units for liquids - Common safety requirements

Pumps and pump units for liquids - Common safety requirements

Short link chain for lifting purposes - Safety - Part 1: General conditions of acceptance

Short link chain for lifting purposes - Safety - Part 2: Medium tolerance chain for chain slings - Grade 8

Short link chain for lifting purposes - Safety - Part 3: Medium tolerance chain for chain slings - Grade 4

Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8

Short link chain for lifting purposes - Safety - Part 5: Chain slings - Grade 4

Short link chain for lifting purposes - Safety - Part 6: Chain slings - Specification for information for use and maintenance to be provided by the manufacturer

Short link chain for lifting purposes - Safety - Part 7: Fine tolerance hoist chain, Grade T (Types T, DAT and DT)

Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines

Nota 2

Safety of woodworking machines - One side moulding machines with rotating tool - Part 2: Single spindle hand fed/integrated fed routing machines

Nota 2

Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines

Nota 2

Safety of woodworking machines - Hand fed surface planing machines

Nota 2

Safety of woodworking machines - One side thickness planing machines

Nota 2

Safety of woodworking machines - Surface planing and thicknessing machines

Nota 2

Safety of machinery - Safety requirements for pressure metal diecasting units

Agricultural and forestry machinery - Reel machines for irrigation - Safety

Agricultural and forestry machinery - Centre pivot and moving lateral types irrigation machines - Safety

Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements

Footwear manufacturing machines - Lasting machines - Safety requirements

Safety of woodworking machines - Combined woodworking machines

Nota 2

Stationary training equipment - Part 6: Treadmills, additional specific safety requirements and test methods

Tannery machines - Reciprocating roller machines - Safety requirements

Tannery machines - Reciprocating roller machines - Safety requirements

Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements

Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 2: Printing and varnishing machines including pre-press machinery

Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 3: Cutting machines

Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 4: Bookbinding, paper converting and finishing machines

Compressors and vacuum pumps - Safety requirements - Part 1: Air compressors

Compressors and vacuum pumps - Safety requirements - Part 2: Vacuum pumps

Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors

Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 1: Classification - General and safety requirements

Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 2: Verification of general and safety requirements

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 1: Common requirements

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 2: Barking drums

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 3: Rereelers and winders

Nota 2

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 4: Pulpers and their loading facilities

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 5: Sheeters

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 6: Calender

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 7: Chests

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 8: Refining plants

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 14: Reel splitter

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 16: Paper and board making machines

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 21: Coating machines

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 22: Wood Grinders

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 26: Roll packaging machines

Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 27: Roll handling systems

Plastics and rubber machines - Extruders and extrusion lines - Part 1: Safety requirements for extruders

Plastics and rubber machines - Extruders and extrusion lines - Part 3: Safety requirements for haul-offs

Safety of industrial trucks - Electrical requirements - Part 1: General requirements for battery powered trucks

Safety of industrial trucks - Electrical requirements - Part 2: General requirements of internal combustion engine powered trucks

Safety of industrial trucks - Electrical requirements - Part 3: Specific requirements for the electric power transmission systems of internal combustion engine powered trucks

Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table

Safety of woodworking machines - Tenoning machines - Part 2: Double end tenoning and/or profiling machines fed by chain or chains

Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers

Safety of woodworking machines - Tenoning machines - Part 5: One side profiling machines with fixed table and feed rollers or feed chain

Foundry machinery - Safety requirements for ladles, pouring equipment, centrifugal casting machines, continuous and semi continuous casting machines

Foundry machinery - Safety requirements for abrasive blasting equipment

Safety of machinery - Noise test code for foundry machines and equipment

Agricultural machinery - Silos stationary unloaders for round silos - Safety

Dock levellers - Safety requirements

Plastics and rubber machines - Two-roll mills - Safety requirements

Nota 2

Rough-terrain trucks - Safety requirements and verification - Part 1: Variable-reach trucks

Nota 2

Rough-terrain trucks - Safety requirements and verification - Part 2: Slewing variable-reach trucks

Textile slings - Safety - Part 1: Flat woven webbing slings made of man-made fibres for general purpose use

Textile slings - Safety - Part 2: Roundslings made of man-made fibres for general purpose use

Textile slings - Safety - Part 4: Lifting slings for general service made from natural and man-made fibre ropes

Vehicle lifts

Nota 2

Mobile or movable jacks and associated lifting equipment

Lifting platforms - Mast climbing work platforms

Atenţie: Prezenta publicaţie nu se referă la punctul 5.3.2.4, ultimul paragraf din 7.1.2.12, tabelul 8 şi figura 9 din standardul EN 1495: 1997, care nu beneficiază de prezumţia de conformitate cu dispoziţiile Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014

.

Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles

Nota 2

Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles

Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles

Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles

Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles

Nota 2

Safety of industrial trucks - Additional requirements for automated functions on trucks

Dryers and ovens, in which flammable substances are released - Safety requirements

Nota 2

Industrial thermoprocessing equipment - Noise test code for industrial thermoprocessing equipment including its ancillary handling equipment

Machine-tools safety - Safety requirements for the design and construction of work holding chucks

Conveyor belts - Drum friction testing

Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landings

Nota 2

Safety requirements for lifting tables - Part 2: Lifting tables serving more than 2 fixed landings of a building, for lifting goods with a vertical travel speed not exceeding 0,15 m/s

Plastics and rubber machines - Reaction moulding machines - Part 1: Safety requirements for metering and mixing units

Food processing machinery - Basic concepts - Part 2: Hygiene requirements

Food processing machinery - Rotary rack ovens - Safety and hygiene requirements

Food processing machinery - Dough sheeters - Safety and hygiene requirements

Nota 2

Components for slings - Safety - Part 1: Forged steel components, Grade 8

Components for slings - Safety - Part 2: Forged steel lifting hooks with latch, Grade 8

Components for slings - Safety - Part 3: Forged steel self-locking hooks - Grade 8

Components for slings - Safety - Part 4: Links, Grade 8

Components for slings - Safety - Part 5: Forged steel lifting hooks with latch - Grade 4

Components for slings - Safety - Part 6: Links - Grade 4

Food processing machinery - Vegetable cutting machines - Safety and hygiene requirements

Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines

Equipment and components intended for use in potentially explosive atmospheres in underground mines

Safety of industrial trucks - Operation in potentially explosive atmospheres - Use in flammable gas, vapour, mist and dust

Nota 2

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods

Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers

Hydraulic platforms (HPs) for fire fighting and rescue services - Safety requirements and testing

Nota 2

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set legs and rams

Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems

Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws

Nota 2

Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines

Nota 2

Safety requirements for suspended access equipment - Design calculations, stability criteria, construction - Examinations and tests

Nota 2

High pressure water jet machines - Safety requirements - Part 1: Machines

High-pressure water jet machines - Safety requirements - Part 2: Hoses, hose lines and connectors

Footwear manufacturing machines - Footwear moulding machines - Safety requirements

Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance

Nota 2

Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance

Nota 2

Agricultural machinery - Trailers with tipping body - Safety

Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches

Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 5: Circular sawbenches/up-cutting cross-cut sawing machines

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading

Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 11: Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws)

Nota 2

Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws

Nota 2

Machines for underground mines - Mobile machines working underground - Safety - Part 1: Rubber tyred vehicles

Machines for underground mines - Mobile machines working underground - Safety - Part 2: Rail locomotives

Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements

Nota 2

Aircraft ground support equipment - General requirements - Part 2: Stability and strength requirements, calculations and test methods

Aircraft ground support equipment - General requirements - Part 3: Vibration measurement methods and reduction

Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction

Atomising and spraying equipment for coating materials - Safety requirements

Nota 2

Food processing machinery - Slicing machines - Safety and hygiene requirements

Acoustics - Noise test code for compressors and vacuum pumps - Engineering method (Grade 2)

Earth-moving machinery - Minimum access dimensions

Earth-moving machinery - Access systems

Nota 2

Earth-moving machinery - Laboratory evaluations of protective structures - Specifications for deflection-limiting volume

Nota 2

Forged steel eyebolts grade 4 for general lifting purposes

Forged steel eyebolts grade 4 for general lifting purposes

Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope

Earth-moving machinery - Falling-object protective structures - Laboratory tests and performance requirements

Earth-moving machinery - Wheeled or high-speed rubber-tracked machines - Performance requirements and test procedures for brake systems

Nota 2

Earth-moving machinery - Guards - Definitions and requirements

Earth-moving machinery - Roll-over protective structures - Laboratory tests and performance requirements

Industrial trucks - Safety requirements and verification - Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks

Nota 2

Industrial trucks - Safety requirements and verification - Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks

Industrial trucks - Safety requirements and verification - Part 5: Pedestrian-propelled trucks

Nota 2

Industrial trucks - Safety requirements and verification - Part 5: Pedestrian-propelled trucks

Industrial trucks - Safety requirements and verification - Part 6: Burden and personnel carriers

Nota 2

Industrial trucks - Safety requirements and verification - Part 6: Burden and personnel carriers

Agricultural machinery - Safety - Part 1: General requirements

Nota 2

Agricultural machinery - Safety - Part 5: Power-driven soil-working machines

Agricultural machinery - Safety - Part 5: Power-driven soil-working machines

Agricultural machinery - Safety - Part 6: Sprayers and liquid fertilizer distributors

Agricultural machinery - Safety - Part 6: Sprayers and liquid fertilizer distributors

Agricultural machinery - Safety - Part 7: Combine harvesters, forage harvesters and cotton harvesters

Agricultural machinery - Safety - Part 7: Combine harvesters, forage harvesters and cotton harvesters

Agricultural machinery - Safety - Part 10: Rotary tedders and rakes

Agricultural machinery - Safety - Part 10: Rotary tedders and rakes

Agricultural machinery - Safety - Part 11: Pick-up balers

Nota 2

Agricultural machinery - Safety - Part 12: Rotary disc and drum mowers and flail mowers

Nota 2

Agricultural machinery - Safety - Part 12: Rotary disc and drum mowers and flail mowers

Agricultural machinery - Safety - Part 14: Bale wrappers

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 1: Terminology and common tests

Nota 2

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 2: Pedestrian-controlled lawnmowers

Nota 2

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 2: Pedestrian-controlled lawnmowers

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 2: Pedestrian-controlled lawnmowers

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 3: Ride-on lawnmowers with seated operator

Nota 2

Garden equipment - Safety requirements for combustion-engine-powered lawnmowers - Part 3: Ride-on lawnmowers with seated operator

Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria

Earth-moving machinery - Zones of comfort and reach for controls

Earth-moving machinery - Seat belts and seat belt anchorages - Performance requirements and tests

Earth-moving machinery - Laboratory evaluation of operator seat vibration

Safety requirements for dry-cleaning machines - Part 1: Common safety requirements

Safety requirements for dry-cleaning machines - Part 2: Machines using perchloroethylene

Safety requirements for dry-cleaning machines - Part 3: Machines using combustible solvents

Reciprocating internal combustion engine driven alternating current generating sets - Part 13: Safety

Nota 2

Textile machinery - Noise test code - Part 1: Common requirements

Textile machinery - Noise test code - Part 1: Common requirements

Textile machinery - Noise test code - Part 2: Spinning preparatory and spinning machinery (ISO 9902-2:2001)

Textile machinery - Noise test code - Part 2: Spinning preparatory and spinning machinery

Textile machinery - Noise test code - Part 2: Spinning preparatory and spinning machinery

Textile machinery - Noise test code - Part 3: Nonwoven machinery

Textile machinery - Noise test code - Part 3: Nonwoven machinery

Textile machinery - Noise test code - Part 3: Nonwoven machinery

Textile machinery - Noise test code - Part 4: Yarn processing, cordage and rope manufacturing machinery

Textile machinery - Noise test code - Part 4: Yarn processing, cordage and rope manufacturing machinery

Textile machinery - Noise test code - Part 4: Yarn processing, cordage and rope manufacturing machinery

Textile machinery - Noise test code - Part 5: Weaving and knitting preparatory machinery

Textile machinery - Noise test code - Part 5: Weaving and knitting preparatory machinery

Textile machinery - Noise test code - Part 5: Weaving and knitting preparatory machinery

Textile machinery - Noise test code - Part 6: Fabric manufacturing machinery

Textile machinery - Noise test code - Part 6: Fabric manufacturing machinery

Textile machinery - Noise test code - Part 6: Fabric manufacturing machinery

Textile machinery - Noise test code - Part 7: Dyeing and finishing machinery

Textile machinery - Noise test code - Part 7: Dyeing and finishing machinery

Textile machinery - Noise test code - Part 7: Dyeing and finishing machinery

Robots and robotic devices - Safety requirements for industrial robots - Part 1: Robots

Nota 2

Robots and robotic devices - Safety requirements for industrial robots - Part 2: Robot systems and integration

Safety requirements for industrial laundry machinery - Part 1: Common requirements

Safety requirements for industrial laundry machinery - Part 2: Washing machines and washer-extractors

Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines including component machines

Safety requirements for industrial laundry machinery - Part 4: Air dryers

Safety requirements for industrial laundry machinery - Part 5: Flatwork ironers, feeders and folders

Safety requirements for industrial laundry machinery - Part 6: Ironing and fusing presses

Powered hand-held hedge trimmers - Safety

Powered hand-held hedge trimmers - Safety

Industrial sewing machines - Safety requirements for sewing machines, units and systems

Industrial sewing machines - Safety requirements for sewing machines, units and systems

Reciprocating internal combustion engines - Handle starting equipment - Part 1: Safety requirements and tests

Reciprocating internal combustion engines - Handle starting equipment - Part 2: Method of testing the angle of disengagement

Textile machinery - Safety requirements - Part 1: Common requirements

Textile machinery - Safety requirements - Part 2: Spinning preparatory and spinning machines

Textile machinery - Safety requirements - Part 2: Spinning preparatory and spinning machines

Textile machinery - Safety requirements - Part 2: Spinning preparatory and spinning machines

Textile machinery - Safety requirements - Part 3: Nonwoven machinery

Textile machinery - Safety requirements - Part 3: Nonwoven machinery

Textile machinery - Safety requirements - Part 3: Nonwoven machinery

Textile machinery - Safety requirements - Part 4: Yarn processing, cordage and rope manufacturing machinery

Textile machinery - Safety requirements - Part 4: Yarn processing, cordage and rope manufacturing machinery

Textile machinery - Safety requirements - Part 4: Yarn processing, cordage and rope manufacturing machinery

Textile machinery - Safety requirements - Part 5: Preparatory machinery to weaving and knitting

Textile machinery - Safety requirements - Part 5: Preparatory machinery to weaving and knitting

Textile machinery - Safety requirements - Part 5: Preparatory machinery to weaving and knitting

Textile machinery - Safety requirements - Part 6: Fabric manufacturing machinery

Textile machinery - Safety requirements - Part 6: Fabric manufacturing machinery

Textile machinery - Safety requirements - Part 6: Fabric manufacturing machinery

Textile machinery - Safety requirements - Part 7: Dyeing and finishing machinery

Textile machinery - Safety requirements - Part 7: Dyeing and finishing machinery

Textile machinery - Safety requirements - Part 7: Dyeing and finishing machinery

Optics and photonics - Lasers and laser-related equipment - Vocabulary and symbols

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 1: Assembly power tools for non-threaded mechanical fasteners

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 3: Drills and tappers

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 4: Non-rotary percussive power tools

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 5: Rotary percussive drills

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 7: Grinders

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 8: Sanders and polishers

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 9: Die grinders

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 11: Nibblers and shears

Nota 2

Hand-held non-electric power tools - Safety requirements - Part 12: Circular, oscillating and reciprocating saws

Nota 2

Lasers and laser-related equipment - Laser device - Minimum requirements for documentation

Nota 2

Safety of machinery - Laser processing machines - Part 1: General safety requirements

Safety of machinery - Laser processing machines - Part 2: Safety requirements for hand-held laser processing devices

Safety of machinery - Laser processing machines - Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2)

)

Optics and photonics - Lasers and laser-related equipment - Test methods for laser beam power, energy and temporal characteristics

Nota 2

Machinery for forestry - Safety requirements and testing for pole-mounted powered pruners - Part 1: Machines fitted with an integral combustion engine

Nota 2

Machinery for forestry - Safety requirements and testing for pole-mounted powered pruners - Part 2: Machines for use with back-pack power source

Nota 2

Machinery for forestry - Portable chain-saw safety requirements and testing - Part 1: Chain-saws for forest service

Nota 2

Nota 2

Machinery for forestry - Portable chain-saw safety requirements and testing - Part 2: Chain-saws for tree service

Agricultural and forestry machinery - Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers - Part 1: Machines fitted with an integral combustion engine (

Nota 2

Agricultural and forestry machinery - Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers - Part 2: Machines for use with back-pack power unit

Machinery for forestry - General safety requirements

Nota 2

Conveying, spraying and placing machines for concrete and mortar - Safety requirements

Nota 2

-1+A1:2015

Plastics and rubber machines - Size reduction machines - Part 1: Safety requirements for blade granulators

-3+A1:2015

Plastics and rubber machines - Size reduction machines - Part 3: Safety requirements for shredders

-4+A1:2015

Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators

+A1:2015

Plastics and rubber machines - Internal mixers - Safety requirements

:2014

Electromagnetic compatibility - Product family standard for lifts, escalators and moving walks - Immunity

Nota 2

Food processing machinery - Moulders - Safety and hygiene requirements

Nota 2

Food processing machinery - Automatic dough dividers - Safety and hygiene requirements

Nota 2

Food processing machinery - Intermediate provers - Safety and hygiene requirements

Nota 2

Footwear, leather and imitation leather goods manufacturing machines - Cutting and punching machines - Safety requirements

Safety of industrial trucks - Test methods for measuring noise emissions

Cranes safety - Requirements for health and safety - Part 2: Limiting and indicating devices

Tunnelling machines - Air locks - Safety requirements

Nota 2

Tunnelling machines - Road headers and continuous miners - Safety requirements

Nota 2

Builders' hoists for goods - Part 1: Hoists with accessible platforms

Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices

Builders hoists for persons and materials with vertically guided cages

Nota 2

Liquid pumps - Safety requirements - Procedure for hydrostatic testing

Footwear, leather and imitation leather goods manufacturing machines - Shoe and leather presses - Safety requirements

Food processing machinery - Circular saw machines - Safety and hygiene requirements

Food processing machinery - Band saw machines - Safety and hygiene requirements

Nota 2

Plastics and rubber machines - Calenders - Safety requirements

Aircraft ground support equipment - Specific requirements - Part 1: Passenger stairs

Nota 2

Aircraft ground support equipment - Specific requirements - Part 2: Catering vehicles

Nota 2

Aircraft ground support equipment - Specific requirements - Part 3: Conveyor belt vehicles

Nota 2

Aircraft ground support equipment - Specific requirements - Part 4: Passenger boarding bridges

Nota 2

Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment

Aircraft ground support equipment - Specific requirements - Part 6: Deicers and de-icing/anti-icing equipment

Nota 2

Aircraft ground support equipment - Specific requirements - Part 7: Air-craft movement equipment

Aircraft ground support equipment - Specific requirements - Part 8: Maintenance stairs and platforms

Aircraft ground support equipment - Specific requirements - Part 9: Container/Pallet loaders

Nota 2

Aircraft ground support equipment - Specific requirements - Part 10: Container/Pallet transfer transporters

Aircraft ground support equipment - Specific requirements - Part 12: Potable water service equipment

Nota 2

Aircraft ground support equipment - Specific requirements - Part 13: Lavatory service equipment

Nota 2

Aircraft ground support equipment - Specific requirements - Part 14: Disabled/incapacitated passenger boarding vehicles

Nota 2

Aircraft ground support equipment - Specific requirements - Part 15: Baggage and equipment tractors

Aircraft ground support equipment - Specific requirements - Part 16: Air start equipment

Aircraft ground support equipment - Specific requirements - Part 17: Air conditioning equipment

Aircraft ground support equipment - Specific requirements - Part 18: Nitrogen or Oxygen units

Aircraft ground support equipment - Specific requirements - Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions

Aircraft ground support equipment - Specific requirements - Part 20: Electrical ground power units

Underground mining machinery - Specification for the safety requirements of armoured face conveyors

Food processing machinery - Mincing machines - Safety and hygiene requirements

Core drilling machines on stand - Safety

Food processing machinery - Derinding-, skinning- and membrane removal machines - Safety and hygiene requirements

Steel wire ropes - Safety - Part 1: General requirements

Steel wire ropes - Safety - Part 2: Definitions, designation and classification

Steel wire ropes - Safety - Part 3: Information for use and maintenance

Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications

Steel wire ropes - Safety - Part 10: Spiral ropes for general structural applications

Footwear, leather and imitation leather goods manufacturing machines - Modular shoe repair equipment - Safety requirements

Plastics and rubber machines - Thermoforming machines - Safety requirements

Nota 2

Machine tools - Safety - Machining centres

Masonry and stone cutting-off machines for job site - Safety

Food processing machinery - Filling machines and auxiliary machines - Safety and hygiene requirements

Food processing machinery - Centrifugal machines for processing edible oils and fats - Safety and hygiene requirements

Agricultural machinery - Front loaders - Safety

Footwear, leather and imitation leather goods manufacturing machines - Noise test code - Common requirements

Centrifuges - Common safety requirements

Nota 2

Acoustics - Noise test code for fastener driving tools - Engineering method

Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements

Machinery for the supply and circulation of coating materials under pressure - Safety requirements

Safety of machine tools - Hydraulic press brakes

Nota 2

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines

Nota 4

prezumţia de conformitate a standardului înlocuit

Nota 1

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-2: Pipe making machines manufacturing in the horizontal axis

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-3: Pipe prestressing machines

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-4: Concrete pipe coating machines

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of prestressed products

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)

Industrial, commercial and garage doors and gates - Installation and use

Atenţie: În ceea ce priveşte punctul 5.1 şi anexa D, prezenta publicaţie nu se referă la referinţa la EN 12453: 2000 a cărui aplicare nu conferă prezumţie de conformitate cu cerinţele esenţiale de sănătate şi siguranţă prevăzute de pct.6-12, 22,31, 32, 80-82, 84-86, 88,89, 96, 97 şi 122 din Anexa nr.1 la Reglementarea tehnică "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014

.

Earth-moving machinery - Rubber-tyred machines - Steering requirements

Nota 2

Cranes - Information for use and testing - Part 1: Instructions

Cranes - Information for use and testing - Part 2: Marking

Concrete compactors and smoothing machines - Safety

Nota 2

Footwear, leather and imitation leather manufacturing machines - Nailing machines - Safety requirements

Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors

Safety of machine tools - Drilling machines

Agricultural and forestry machinery - Pedestrian controlled motor mowers - Safety

Safety of woodworking machines - Four sided moulding machines

Nota 2

Thermal cleaning systems for exhaust gas from surface treatment equipment - Safety requirements

Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing

Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements

Nota 2

Food processing machinery - Food processors and blenders - Safety and hygiene requirements

Food processing machinery - Hand-held blenders and whisks - Safety and hygiene requirements

Food processing machinery - Hand-held blenders and whisks - Safety and hygiene requirements

Food processing machinery - Beam mixers - Safety and hygiene requirements

Food processing machinery - Rotating bowl cutters - Safety and hygiene requirements

Conveyor belts - Fire simulation flammability testing - Part 1: Propane burner tests

Nota 2

Conveyor belts - Fire simulation flammability testing - Part 2: Large scale fire test

Conveyor belts for general purpose use - Electrical and flammability safety requirements

Nota 2

Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements

Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 2: Safety of machines using water based cleaning liquids

Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 3: Safety of machines using flammable cleaning liquids

Machines for surface cleaning and pretreatment of industrial items using liquids and vapours - Part 4: Safety of machines using halogenated solvents

Tractors and machinery for agriculture and forestry - Power take-off (PTO) drive shafts and their guards - Safety

Industrial, commercial and garage doors and gates - Safety devices for power operated doors and gates - Requirements and test methods

Coating plants - Spray booths for application of organic powder coating material - Safety requirements

Food processing machinery - Portable and/or hand-guided machines and appliances with mechanically driven cutting tools - Safety and hygiene requirements

Cranes - Loader cranes

Nota 2

Cranes - Mobile cranes

Nota 2

Cranes - General design - Part 1: General principles and requirements

Nota 2

Crane safety - General design - Part 2: Load actions

Nota 2

Cranes - General Design - Part 3-1: Limit States and proof competence of steel structure

Nota 2

Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems

Cranes - General design - Part 3-3: Limit states and proof of competence of wheel/rail contacts

Cranes - General design - Part 3-5: Limit states and proof of competence of forged hooks

Maintenance for lifts and escalators - Rules for maintenance instructions

Machines for road surface cleaning - Safety requirements

Road surface treatment machines - Safety requirements

Nota 2

Winter service machines - Safety requirements

Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment - Accuracy grades 2 and 3

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 2: Storage, handling and transportation equipment outside the factory

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 4: Tilting tables

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 6: Machines for break-out

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 9: Washing installations

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 11: Drilling machines

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 1: Gob feeder

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 2: Handling machines for feeding

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 3: IS machines

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 5: Presses

Safety of industrial trucks - Test methods for measuring vibration

Ceramic machines - Safety - Loading and unloading of fine clay tiles

Tannery machines - Splitting and bandknife shearing machines - Safety requirements

Tannery machines - Roller coating machines - Safety requirements

Tannery machines - Rotating process vessels - Safety requirements

Agricultural machinery - Potato harvesting equipment - Safety

Internal blinds - Performance requirements including safety

Nota 2

Internal blinds - Performance requirements including safety

Safety of machine tools - Milling machines (including boring machines)

Safety of machine tools - Milling machines (including boring machines)

Cranes - Safety - Design - Requirements for equipment

SM SR EN 13135-2+A1:2011

Nota 2

Agricultural machinery - Sugar beet and fodder beet harvesting equipment - Safety

Cranes - Safety - Non-fixed load lifting attachments

Cranes - Safety - Hand powered cranes

Double acting hydraulic rescue tools for fire and rescue service use - Safety and performance requirements

Nota 2

Food processing machinery - Vegetable peelers - Safety and hygiene requirements

Industrial, commercial, garage doors and gates - Product standard, performance characteristics

Nota 2

Food processing machinery - Bowl lifting and tilting machines - Safety and hygiene requirements

Pasta processing plants - Dryers and coolers - Safety and hygiene requirements

Coating plants - Combined booths - Safety requirements

Ceramic machines - Safety - Transfer platforms and cars

Pasta processing plants - Pasta presses - Safety and hygiene requirements

Pasta processing plants - Spreader, stripping and cutting machine, stick return conveyor, stick magazine - Safety and hygiene requirements

Food processing machinery - Mixers with horizontal shafts - Safety and hygiene requirements

Food processing machinery - Pie and tart machines - Safety and hygiene requirements

Terminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings

Terminations for steel wire ropes - Safety - Part 2: Splicing of eyes for wire rope slings

Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing

Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing

Nota 2

Terminations for steel wire ropes - Safety - Part 5: U-bolt wire rope grips

Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket

Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket

Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging

Steel wire rope slings - Safety - Part 1: Slings for general lifting service

Steel wire rope slings - Safety - Part 2: Specification for information for use and maintenance to be provided by the manufacturer

Steel wire rope slings - Safety - Part 3: Grommets and cable-laid slings

Plastics and rubber machines - Winding machines for film or sheet - Safety requirements

Nota 2

Agricultural and forestry machinery - Inter-row mowing units - Safety

Footwear, leather and imitation leather goods manufacturing machines - Splitting, skiving, cutting, cementing and cement drying machines - Safety requirements

Robots and robotic devices - Safety requirements for personal care robots

Highway maintenance machines - Safety requirements

Nota 2

Earth-moving machinery - Tip-over protection structure (TOPS) for compact excavators - Laboratory tests and performance requirements

Food processing machinery - Curing injection machines - Safety and hygiene requirements

Cranes - Controls and control stations

External blinds and awnings - Performance requirements including safety

Nota 2

External blinds and awnings - Performance requirements including safety

Food processing machinery - Mixing machines - Safety and hygiene requirements

Cranes - Access

Food processing machinery - Fixed deck oven loaders - Safety and hygiene requirements

Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units

Nota 2

Food processing machinery - Salad dryers - Safety and hygiene requirements

Shutters and external venetian blinds - Performance requirements including safety

Nota 2

Safety of machinery - Safety requirements for tube forming and rolling mills and their finishing line equipment

Garden equipment - Integrally powered shredders/chippers - Safety

Garden equipment - Integrally powered shredders/chippers - Safety

Garden equipment - Pedestrian controlled lawn aerators and scarifiers - Safety

Nota 2

Food processing machinery - Bulk milk coolers on farms - Requirements for performance, safety and hygiene

Nota 2

Safety of machine tools - Pneumatic presses

Cranes - Offshore cranes - Part 1: General-purpose offshore cranes

Floor cutting-off machines - Safety

Food processing machinery - Portion cutting machines - Safety and hygiene requirements

Nota 2

Food processing machinery - Cubes cutting machinery - Safety and hygiene requirements

Nota 2

Food processing machinery - Clipping machines - Safety and hygiene requirements

Food processing machinery - Cooking kettles equipped with powered stirrer and/or mixer - Safety and hygiene requirements

Forged steel shackles for general lifting purposes - Dee shackles and bow shackles - Grade 6 - Safety

Liquid pumps - Safety requirements - Agrifoodstuffs equipment. Design rules to ensure hygiene in use

Nota 2

Food processing machinery - Bread slicers - Safety and hygiene requirements

Railway applications - Track - Safety requirements for portable machines and trolleys for construction and maintenance

Machine tools - Safety - Guillotine shears

Safety of machinery - Equipment for power driven parking of motor vehicles - Safety and EMC requirements for design, manufacturing, erection and commissioning stages

Agricultural and forestry machinery - Solid fertilizer distributors - Safety

Nota 2

Agricultural and forestry machinery - Seed drills - Safety

Railway applications - Track - Railbound construction and maintenance machines - Part 3: General safety requirements

Nota 2

High rise aerial appliances for fire and rescue service use - Turntable ladders with combined movements - Safety and performance requirements and test methods

Nota 2

High rise aerial appliances for fire and rescue service use - Turntable ladders with sequential movements - Safety and performance requirements and test methods

Nota 2

Safety of machine tools - Transfer and special-purpose machines

Safety of machine tools - Transfer and special-purpose machines

Cranes - Manually controlled load manipulating devices

Reciprocal internal combustion engines - Recoil starting equipment - General safety requirements

Cranes - Safety - Tower cranes

Surface treatment equipment - Noise test code for surface treatment equipment including its ancillary handling equipment - Accuracy grades 2 and 3

Fire-fighting pumps - Portable pumps - Safety and performance requirements, tests

Cranes - Power driven winches and hoists - Part 1: Power driven winches

Cranes - Power driven winches and hoists - Part 1: Power driven winches

Cranes - Power driven winches and hoists - Part 2: Power driven hoists

Cranes - Power driven winches and hoists - Part 2: Power driven hoists

Cranes - Equipment for the lifting of persons - Part 2: Elevating control stations

Food processing machinery - Baguette slicers - Safety and hygiene requirements

Safety of machinery - Safety requirements for extrusion presses for steel and non-ferrous metals

Continuous handling equipment and systems - General safety requirements for continuous handling equipment for opencast lignite mining

Safety of machinery - Safety requirements for hydraulically powered open die hot forging presses for the forging of steel and non-ferrous metals

Safety of machinery - Secondary steelmaking - Machinery and equipment for treatment of liquid steel

Safety of machinery - Safety requirements for machinery and equipment for production of steel by electric arc furnaces

Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 1: Classification, general and safety requirements

Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Part 2: Verification of general and safety requirements

Plastics and rubber machines - Bandknife cutting machines for block foams - Safety requirements

Garden equipment - Walk-behind combustion engine powered trimmers - Safety

Agricultural and forestry machinery and gardening equipment - Pedestrian controlled and hand-held machines - Determination of accessibility of hot surfaces

Food processing machinery - Dishwashing machines with conveyor - Safety and hygiene requirements

Food processing machinery - Machinery for grinding and processing flour and semolina - Safety and hygiene requirements

Conveyor belts for use in underground installations - Electrical and flammability safety requirements

Nota 2

Agricultural and forestry machinery - Electromagnetic compatibility - Test methods and acceptance criteria

Cranes - Slewing jib cranes

Safety of industrial trucks - Self propelled variable reach trucks - Specification, performance and test requirements for longitudinal load moment indicators and longitudinal load moment limiters

Cranes - Bridge and gantry cranes

Nota 2

Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 4: General requirements

Transportable wall saw and wire saw equipment for job site - Safety

Cranes - Requirements for container handling spreaders

Snow grooming equipment - Safety requirements

Nota 2

Safety of machinery - Safety requirements for strip processing line machinery and equipment

Plastics and rubber machines - Film converting machines for bags and sacks - Safety requirements

Safety of Machinery - Safety requirements for hot flat rolling mills

Safety of Machinery - Safety requirements for cold flat rolling mills

Power-operated mobile racking and shelving, carousels and storage lifts - Safety requirements

Machines and plants for mining and tooling of natural stone - Safety requirements for gang saws

Machines and installations for the exploitation and processing of natural stone - Safety - Requirements for diamond wire saws

Machines and plants for mining and tooling of natural stone - Safety - Requirements for chain- and belt-slotting machines

Food processing machinery - Automatic back splitting machines of butchery carcasses - Safety and hygiene requirements

Petrol filling stations - Safety requirements for the construction of submersible pump assemblies

Garden equipment - Garden blowers, vacuums and blower/vacuums - Safety

Nota 2

Machines and plants for mining and tooling of natural stone - Safety - Requirements for edge finishing machines

Agricultural tractors and self-propelled sprayers - Protection of the operator (driver) against hazardous substances - Part 1: Cab classification, requirements and test procedures

Nota 2

Agricultural tractors and self-propelled sprayers - Protection of the operator (driver) against hazardous substances - Part 2: Filters, requirements and test procedures

Nota 2

Safety for conveyor belts for winter sport or leisure use

Hand-held non-electric power tools - Noise measurement code - Engineering method (grade 2)

Railway applications - Track - Road-rail machines and associated equipment - Part 2: General safety requirements

Nota 2

Food processing machinery - Machines for processing fresh and filled pasta (tagliatelle, cannelloni, ravioli, tortellini, orecchiette and gnocchi) - Safety and hygiene requirements

Agricultural machinery - Fixed guards and interlocked guards with or without guard locking for moving transmission parts

Nota 2

Rough-terrain variable reach trucks - Visibility - Test methods and verification

Food processing machinery - Smokehouses - Safety and hygiene requirements

Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools

Safety of machinery - Safety requirements for bar mills, structural steel mills and wire rod mills

Railway applications - Track - Trailers and associated equipment - Part 2: General safety requirements

Railway applications - Track - Demountable machines and associated equipment - Part 2: General safety requirements

All terrain vehicles (ATVs - Quads) - Safety requirements and test methods

All terrain vehicles (ATVs - Quads) - Safety requirements and test methods

Power operated pedestrian doorsets - Safety in use - Requirements and test methods

Power operated pedestrian doorsets - Safety in use - Requirements and test methods

Ride-on, motorized vehicles intended for the transportation of persons and not intended for use on public roads - Single-track two-wheel motor vehicles - Safety requirements and test methods

Machine tools - Safety - Stationary grinding machines

Nota 2

Machine tools - Safety - Sawing machines for cold metal

Nota 2

Agricultural and forestry machinery - Environmental requirements for sprayers - Part 1: General

Agricultural and forestry machinery - Environmental requirements for sprayers - Part 2: Horizontal boom sprayers

Agricultural and forestry machinery - Environmental requirements for sprayers - Part 3: Sprayers for bush and tree crops

Agricultural and forestry machinery - Environmental requirements for sprayers - Part 4: Fixed and semi-mobile sprayers

Tunnelling machinery - Safety requirements

SM SR EN 12336+A1:2011

Nota 2

Safety of Industrial Trucks - Dynamic tests for verification of lateral stability - Counterbalanced Trucks

Drilling and foundation equipment - Safety - Part 1: Common requirements

SM SR EN 996+A3:2011

Nota 2

Drilling and foundation equipment - Safety - Part 2: Mobile drill rigs for civil and geotechnical engineering, quarrying and mining

SM SR EN 996+A3:2011

Nota 2

Drilling and foundation equipment - Safety - Part 3: Horizontal directional drilling equipment (HDD)

SM SR EN 996+A3:2011

Nota 2

Drilling and foundation equipment - Safety - Part 4: Foundation equipment

SM SR EN 996+A3:2011

Nota 2

Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment

SM SR EN 996+A3:2011

Nota 2

Drilling and foundation equipment - Safety - Part 6: Jetting, grouting and injection equipment

SM SR EN 996+A3:2011

Nota 2

Drilling and foundation equipment - Safety - Part 7: Interchangeable auxiliary equipment

SM SR EN 996+A3:2011

Nota 2

Leisure karts - Part 1: Safety requirements and test methods for karts

Nota 2

Agricultural machinery and tractors - Safety of higher voltage electrical and electronic components and systems - Part 1: General requirements

Self-propelled agricultural machinery - Assessment of stability - Part 1: Principles

Self-propelled agricultural machinery - Assessment of stability - Part 2: Determination of static stability and test procedures

Agricultural machinery - Backhoes - Safety

Machines for compacting waste materials or recyclable fractions - Horizontal baling presses - Safety requirements

Industrial trucks - Safety requirements and verification - Part 1: Supplementary requirements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks

Nota 2

Industrial trucks - Safety requirements and verification - Part 5: Supplementary requirements for pedestrian-propelled trucks

Industrial trucks - Safety requirements and verification - Part 6: Supplementary requirements for burden and personnel carriers

Fire-fighting - Positive-pressure proportioning systems (PPPS) and compressed-air foam systems (CAFS)

Plastics and rubber machines - Tyre curing machines - Safety requirements

Machines for compacting waste materials or recyclable fractions - Compactors - Safety requirements

Machines for compacting waste materials or recyclable fractions - Vertical baling presses - Safety requirements

Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 3: Series development, hardware and software

Tractors and machinery for agriculture and forestry - Safety-related parts of control systems - Part 4: Production, operation, modification and supporting processes

Food processing machinery - Automatic industrial slicing machines - Safety and hygiene requirements

Safety of machinery - Safety requirements for steel converter and associated equipment

Cranes - Light crane systems

Safety of thermal cutting machines

Safety of woodworking machines - Edge-banding machines fed by chain(s)

Nota 2

Woodworking machines - Safety - Part 1: Common requirements

Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines

Woodworking machines - Safety - Part 5: Dimension saws

Nota 2

Building construction machinery and equipment - Portable, hand-held, internal combustion engine driven cut-off machines - Safety requirements

Nota 2

Equipment for crop protection - Knapsack sprayers - Part 1: Safety and environmental requirements

Equipment for crop protection - Knapsack sprayers - Part 2: Test methods

Liquid pumps and pump units - Noise test code - Grades 2 and 3 of accuracy

Nota 2

Forestry and gardening machinery - Vibration test code for portable hand-held machines with internal combustion engine - Vibration at the handles

Nota 2

Forestry and gardening machinery - Noise test code for portable hand-held machines with internal combustion engine - Engineering method (Grade 2 accuracy)

Nota 2

Machine tools - Safety - Turning machines

Nota 2.1

Agricultural and forestry machinery - Knapsack combustion-engine-driven mistblowers - Safety requirements

Machine tools - Safety - Electro-discharge machines

Nota 2

Machine tools - Safety - Electro-discharge machines

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 1: Angle and vertical grinders

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 1: Angle and vertical grinders

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 2: Wrenches, nutrunners and screwdrivers

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 3: Polishers and rotary, orbital and random orbital sanders

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 4: Straight grinders

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 5: Drills and impact drills

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 5: Drills and impact drills

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 6: Rammers

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 7: Nibblers and shears

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 8: Saws, polishing and filing machines with reciprocating action and saws with oscillating or rotating action

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 8: Saws, polishing and filing machines with reciprocating action and saws with oscillating or rotating action

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 9: Scaling hammers and needle scalers

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 10: Percussive drills, hammers and breakers

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 11: Stone hammers

Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 12: Die grinders

Standarde de tip B

Standardele de tip B abordează aspecte specifice siguranţei maşinilor sau diferite tipuri de protecţie care pot fi utilizate pentru o gamă largă de maşini. Aplicarea specificaţiilor standardelor de tip B conferă o prezumţie de conformitate cu cerinţele esenţiale de sănătate şi siguranţă ale Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014

la care acestea se referă dacă un standard de tip C sau evaluarea riscurilor de către producător arată că o soluţie tehnică specificată de standardul de tip B este adecvată pentru categoria sau modelul specific de maşină în cauză. Aplicarea standardelor de tip B care oferă specificaţii pentru componentele de siguranţă care sunt introduse pe piaţă separat conferă o prezumţie de conformitate pentru componentele de siguranţă în cauză şi pentru cerinţele esenţiale de sănătate şi siguranţă care fac obiectul standardelor.

Safety of machinery - Electrical equipment of machines - Part 1: General requirements

Safety of machinery - Electrical equipment of machines - Part 1: General requirements

Safety of machinery - Electrical equipment of machines - Part 1: General requirements

Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV

Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV

Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines

Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment

Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals

Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking

Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators

Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests

Nota 2

EN 61496-1:2004/A1:2008

Nota 2

Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional

Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems

IEC 62061:2005/A1:2012

Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems

Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems

Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems

Standarde de tip C

Standardele de tip C oferă specificaţii pentru o categorie dată de maşini. Diferitele tipuri de maşini aparţinînd categoriei care face obiectul unui standard de tip C au o destinaţie asemănătoare şi prezintă riscuri similare. Standardele de tip C se pot referi la standarde de tip A sau B, indicînd care dintre specificaţiile standardelor de tip A sau B se aplică categoriei de maşini în cauză. Atunci cînd, pentru un anumit aspect al siguranţei maşinilor, un standard de tip C se îndepărtează de specificaţiile unui standard de tip A sau B, specificaţiile standardului de tip C au întâietate faţă de specificaţiile standardului de tip A sau B. Aplicarea specificaţiilor unui standard de tip C pe baza evaluării riscurilor de către producător conferă o prezumţie de conformitate cu cerinţele esenţiale de sănătate şi siguranţă ale Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014

, care fac obiectul standardului. Anumite standarde de tip C se compun din mai multe părţi, partea 1 a standardului oferind specificaţii generale aplicabile unei familii de maşini, în timp ce alte părţi ale standardului precizează specificaţiile anumitor categorii de maşini care aparţin familiei, completând sau modificând specificaţiile generale din partea 1. În cazul standardelor de tip C organizate în acest mod, prezumţia de conformitate cu cerinţele esenţiale de sănătate şi siguranţă ale Reglementării tehnice "Maşini industriale", aprobată prin Hotărîrea Guvernului nr.130 din 21 februarie 2014

este conferită prin aplicarea părţii generale 1 a standardului împreună cu partea specifică corespunzătoare a standardului.

Stationary electrostatic application equipment for ignitable flock material - Safety requirements

Nota 2

Stationary electrostatic application equipment for non-ignitable liquid coating material - Safety requirements

Stationary electrostatic application equipment for non-ignitable liquid coating material - Safety requirements

Safety of household and similar appliances - Particular requirements for mains operated shredders and chippers

Household and similar electrical appliances - Safety - Particular requirements for commercial electric spin extractors

Household and similar electrical appliances - Safety - Particular requirements for commercial electric tumble dryers

Household and similar electrical appliances - Safety - Particular requirements for commercial electric washing machines

Safety of hand-held electric motor operated tools - Particular requirements for spray guns

Safety of hand-held electric motor operated tools - Particular requirements for spray guns

Household and similar electrical appliances - Safety - Part 2-91: Particular requirements for walk-behind and hand-held lawn trimmers and lawn edge trimmers

Household and similar electrical appliances - Safety - Part 2-92: Particular requirements for pedestrian-controlled mains-operated lawn scarifiers and aerators

Household and similar electrical appliances - Safety - Part 2-94: Particular requirements for scissors type grass shears

Household and similar electrical appliances - Safety - Part 2-100: Particular requirements for hand-held mains-operated garden blowers, vacuums and blower vacuums

Safety of household and similar appliances - Part 2-107: Particular requirements for robotic battery powered electrical lawnmowers

Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems

Household and similar electrical appliances - Safety - Part 1: General requirements

SM EN 60335-1:2012/A11:2016

SM SR EN 60335-1:2006/A12:2010

SM SR EN 60335-1:2006/A13:2011

SM SR EN 60335-1:2006/A14:2012

SM SR EN 60335-1:2006/A1:2007

Nota 2.1

EN 60335-1:2002/A15:2011

Nota 2

Household and similar electrical appliances - Safety - Part 1: General requirements

Household and similar electrical appliances - Safety - Part 1: General requirements

Household and similar electrical appliances - Safety - Part 2-8: Particular requirements for shavers, hair clippers and similar appliances

Household and similar electrical appliances - Safety - Part 2-8: Particular requirements for shavers, hair clippers and similar appliances

Household and similar electrical appliances - Safety - Part 2-23: Particular requirements for appliances for skin or hair care

Household and similar electrical appliances - Safety - Part 2-23: Particular requirements for appliances for skin or hair care

Household and similar electrical appliances - Safety - Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements

Household and similar electrical appliances - Safety - Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements

Household and similar electrical appliances - Safety - Part 2-37: Particular requirements for commercial electric deep fat fryers

Household and similar electrical appliances - Safety - Part 2-37: Particular requirements for commercial electric deep fat fryers

Household and similar electrical appliances - Safety - Part 2-37: Particular requirements for commercial electric deep fat fryers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

Household and similar electrical appliances - Safety - Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens

Household and similar electrical appliances - Safety - Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens

Household and similar electrical appliances - Safety - Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens

Household and similar electrical appliances - Safety - Part 2-47: Particular requirements for commercial electric boiling pans

Household and similar electrical appliances - Safety - Part 2-47: Particular requirements for commercial electric boiling pans

Household and similar electrical appliances - Safety - Part 2-47: Particular requirements for commercial electric boiling pans

Household and similar electrical appliances - Safety - Part 2-48: Particular requirements for commercial electric grillers and toasters

Household and similar electrical appliances - Safety - Part 2-48: Particular requirements for commercial electric grillers and toasters

Household and similar electrical appliances - Safety - Part 2-48: Particular requirements for commercial electric grillers and toasters

Household and similar electrical appliances - Safety - Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm

Household and similar electrical appliances - Safety - Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm

Household and similar electrical appliances - Safety - Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm

Household and similar electrical appliances - Safety - Part 2-65: Particular requirements for air-cleaning appliances

Household and similar electrical appliances - Safety - Part 2-65: Particular requirements for air-cleaning appliances

Household and similar electrical appliances - Safety - Part 2-67: Particular requirements for floor treatment machines for commercial use

Nota 2

Household and similar electrical appliances - Safety - Part 2-68: Particular requirements for spray extraction machines, for commercial use

Nota 2

Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush for commercial use

Nota 2

Household and similar electrical appliances - Safety - Part 2-72: Particular requirements for floor treatment machines with or without traction drive, for commercial use

Nota 2

Safety of household and similar appliances - Part 2-77: Particular requirements for pedestrian-controlled walk-behind electrically powered lawn mowers

Household and similar electrical appliances - Safety - Part 2-79: Particular requirements for high pressure cleaners and steam cleaner

Nota 2

Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor

Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor

Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor

Household and similar electrical appliances - Safety - Part 2-95: Particular requirements for drives for vertically moving garage doors for residential use

Household and similar electrical appliances - Safety - Part 2-95: Particular requirements for drives for vertically moving garage doors for residential use

Household and similar electrical appliances - Safety - Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment

Household and similar electrical appliances - Safety - Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment

Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections

Household and similar electrical appliances - Safety - Part 2-103: Particular requirements for drives for gates, doors and windows

Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements

Hand-held motor-operated electric tools - Safety - Part 2-1: Particular requirements for drills and impact drills

Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders

Hand-held motor-operated electric tools - Safety - Part 2-6: Particular requirements for hammers

Hand-held motor-operated electric tools - Safety - Part 2-11: Particular requirements for reciprocating saws (jig and sabre saws)

Hand-held motor-operated electric tools - Safety - Part 2-12: Particular requirements for concrete vibrators

Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws

Hand-held motor-operated electric tools - Safety - Part 2-13: Particular requirements for chain saws

Hand-held motor-operated electric tools - Safety - Part 2-15: Particular requirements for hedge trimmers

Hand-held motor-operated electric tools - Safety - Part 2-15: Particular requirements for hedge trimmers

Hand-held motor-operated electric tools - Safety - Part 2-16: Particular requirements for tackers

Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for routers and trimmers

Hand-held motor-operated electric tools - Safety - Part 2-18: Particular requirements for strapping tools

Hand-held motor-operated electric tools - Safety - Part 2-19: Particular requirements for jointers

Hand-held motor-operated electric tools - Safety - Part 2-19: Particular requirements for jointers

Hand-held motor-operated electric tools - Safety - Part 2-20: Particular requirements for band saws

Hand-held motor-operated electric tools - Safety - Part 2-21: Particular requirements for drain cleaners

IEC 60745-2-21:2002/A1:2008

Hand-held motor-operated electric tools - Safety - Part 2-21: Particular requirements for drain cleaners

Hand-held motor-operated electric tools - Safety - Part 2-22: Particular requirements for cut-off machines

Hand-held motor-operated electric tools - Safety - Part 2-22: Particular requirements for cut-off machines

Hand-held motor-operated electric tools - Safety - Part 2-23: Particular requirements for die grinders and small rotary tools

Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)

Low-voltage switchgear and controlgear - Part 5-5: Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching functio

Low-voltage switchgear and controlgear - Part 5-5: Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching function

Low-voltage switchgear and controlgear - Part 5-5: Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching function

Low-voltage switchgear and controlgear - Part 5-5: Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching function

Safety of transportable motor-operated electric tools - Part 2-3: Particular requirements for planers and thicknessers

Safety of transportable motor-operated electric tools - Part 2-4: Particular requirements for bench grinders

Safety of transportable motor-operated electric tools - Part 2-5: Particular requirements for band saws

Safety of transportable motor-operated electric tools - Part 2-5: Particular requirements for band saws

Safety of transportable motor-operated electric tools - Part 2-8: Particular requirements for single spindle vertical moulders

Safety of transportable motor-operated electric tools - Part 2-9: Particular requirements for mitre saws

Safety of transportable motor-operated electric tools - Part 2-9: Particular requirements for mitre saws

Safety of transportable motor-operated electric tools - Part 2-11: Particular requirements for combined mitre and bench saws

Safety of transportable motor-operated electric tools - Part 2-11: Particular requirements for combined mitre and bench saws

Safety of transportable motor-operated electric tools - Part 2-12: Particular requirements for threading machines

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 1: General requirements

SM EN 60335-1:2012/A11:2016

SM EN 60745-1:2014

SM EN 60745-1:2014/A11:2014

SM EN 61029-1:2014

SM EN 61029-1:2014/A11:2014

Nota 2, alineatul 3

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 1: General requirements

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-2: Particular requirements for hand-held screwdrivers and impact wrenches

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-2: Particular requirements for hand-held screwdrivers and impact wrenches

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type

SM SR EN 60745-2-4:2014/A11:2014

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-5: Particular requirements for hand-held circular saws

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-8: Particular requirements for hand-held shears and nibblers

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-9: Particular requirements for hand-held tappers and threaders

Nota 2

-10 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-9: Particular requirements for hand-held tappers and threaders

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-10: Particular requirements for hand-held mixers

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-11: Particular requirements for hand-held reciprocating saws

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-14: Particular requirements for hand-held planers

SM EN 60745-2-14:2014/A2:2014

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-1: Particular requirements for transportable table saws

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-1: Particular requirements for transportable table saws

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system

Nota 2

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-6: Particular requirements for transportable diamond drills with liquid system

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-9: Particular requirements for transportable mitre saws

SM EN 61029-2-9:2015/A11:2015

Nota 2

-09 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-9: Particular requirements for transportable mitre saws

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines

Nota 2

EN 61029-2-10:2010/A11:2013

Nota 2

-07 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-13: Particular requirements for transportable drills